Menus
File
Load File for Analysis: Duplicates the functionality of the Load File button on the Analyze tab. Its keyboard shortcut is the F2 key.
Load Existing Curve: Loads an exsiting curve (*.ppc) that was previously created by PEMPro. The curve will be loaded into the Program Mount tab. Also, if you are in the AP Raw PE, Celestron, Gemini L4, LX200, or RCX400 tab, a raw curve will be automatically created for that mount.
Create a PE Curve: Duplicates the functionality of the Create a PE Curve button on the Analyze tab. Its keyboard shortcut is the F3 key.
Export PE Data: Duplicates the functionality of the Export Data button on the Analyze tab. Its keyboard shortcut is the F4 key.
Settings
Settings Summary: Opens a dialog that contains all of the configuration settings that were set by the Setup/Calibration Wizard. Here the settings can be reviewed and changed manually if needed. Its keyboard shortcut is the F5 key.
Note:
The setting Movement Direction is also used to control whether or not a PE Curve is inverted or not when you press the From Created PE Curve button in the LX-200 GPS, RCX-400, and LX-200 16 tabs. This is necessary to account for the orientation of the camera. So if your periodic error doubles when using the curve you upload to one of those mounts just invert the curve and reload it.
|
De-Rotate Data: If checked (recommended) PE data will be de rotated to appear on the X-axis. Use the Setup/Calibration Wizard to determine the roll angle of your camera or enter into the Settings Summary dialog the value you obtain from image linking software.
Adjust Data For Declination: If checked (recommended) a star at any declination can be used for measuring periodic error when acquiring PE data.
Calibrate Images when Acquiring Data: If checked the full-frame image is dark subtracted to remove dark noise and hot pixels. However, when PEMPro starts imaging subframes only MaximDL is supported and you will need to set up calibration in MaximDL (see MaximDL documentation).
Disconnect Scope on Disconnect: If checked PEMPro will attempt to disconnect the scope from all applications (not just PEMPro) when you press the Disconnect Scope button in PEMPro.
Disconnect Camera on Disconnect: If checked PEMPro will attempt to disconnect the camera from the camera control application when you press the Disconnect Camera button in PEMPro.
Disable Fundamental Auto-Find: If checked PEMPro will attempt to locate periodic fundamentals in the data when the Create PE Curve button is pressed.
Usually you will not want this item checked but if you wanted to force certain fundamentals to be used, check this item and set the fundamentals in the Mount Configuration Dialog.
Keep Main Form on Top: Forces PEMPro to stay on top even if you click to another application.
Restore Last position when starting: If checked PEMPro will restart in the same screen position and size as when you last closed it down. You can force PEMPro to start in the windows default position by pressing the CTRL key when PEMPro is starting. You can also reset this option with the PEMPro reset tool.
Ask for File and Comments when Acquiring Data: If checked PEMPro will prompt for a filename and comment before starting an Acquire Data and again for final comments after stopping.
Tools
Worm Period Calculator: Brings up the worm period calculator. Its keyboard shortcut is the F6 key.
Show Pulse Test Page: Allows you to send test pulses to your telescope for testing. When checked a new tab appears as below. Its keyboard shortcut is the F7 key.
Wizards
Mount Wizard: brings up the Mount Quick Setup Wizard. Its keyboard shortcut is the F8 key.
Calibration Wizard: brings up the Setup/Calibration Wizard. Its keyboard shortcut is the F9 key.
Help
Help: Shows this help file.
Registration: Shows registration information.
Check for Updates: Checks if there is a newer version available. Internet access is required.
CCDWare Support Forum: If you encounter problems and need support this will take you to the CCDWare support forum.
About: Shows PEMPro's version information.